The effect of Milling Time on Crystal size Sandvik Sanergy

Qolby Sabrina; Ahmad Afandi; Nurhalis Majid

doi:10.21580/jnsmr.2020.6.1.11153

The effect of Milling Time on Crystal size Sandvik Sanergy

* - Lembaga Ilmu Pengetahuan Indonesia, Indonesia

- Lembaga Ilmu Pengetahuan Indonesia, Indonesia

(*) Corresponding Author

DOI: 10.21580/jnsmr.2020.6.1.11153

Abstract
References
Licensing
How to cite

Preliminary study material sandvik sanergy as an alternative material for interconnect applications solid oxide fuel cell (SOFC) have been conducted. Sandvik sanergy was milled for 0, 8, 24, and 48 hr with ball milling planetary MTI Corp. The physical properties of small grain size can affect the strength of the alloy when applied as interconnect. In this study, ratio between ball miller and sandvik sanergy was 1:10 aiming to obtain a small grain size. Crystal size characterized by XRD Rigaku Smartlab, morphology of sandvik sanergy after milling observed using SEM Hithaci SU3500 20 kV. Diameter of particles were observed by particle size analyzer (PSA). Results showed that crystal size as well as particle size tended to decrease with the increasing milling time. Discrepancy occurred at 24 hour of milling time and showed agglomeration.

Keywords: sadvik sanergy, crystal size, milling, morphology sandvik

Alvarez, Estefania, Alan Meier, K. Scott Weil, and Zhenguo Yang. 2011. “Oxidation Kinetics of Manganese Cobaltite Spinel Protection Layers on Sanergy HT for Solid Oxide Fuel Cell Interconnect Applications.” International Journal of Applied Ceramic Technology 8 (1): 33–41. doi:10.1111/j.1744-7402.2009.02421.x.
Amendola, R., P. E. Gannon, S. W. Sofie, and A. J. Weisenstein. 2012. “Interactions between Metallic Interconnects and Ceramic Electrodes in SOFC Operating Environments: Air Side.” Journal of The Electrochemical Society 159 (11): C476–84. doi:10.1149/2.064211jes.
Auger, M. A., V. De Castro, T. Leguey, A. Mu??oz, and R. Pareja. 2013. “Microstructure and Mechanical Behavior of ODS and Non-ODS Fe-14Cr Model Alloys Produced by Spark Plasma Sintering.” Journal of Nuclear Materials 436 (1-3): 68–75. doi:10.1016/j.jnucmat.2013.01.331.
B.Huang, R.J perez. 1995. “Mechanical Induced Crystallyzation of Metglas during High Energy Milling.”
Bilgin, V., I. Akyuz, E. Ketenci, S. Kose, and F. Atay. 2010. “Electrical, Structural and Surface Properties of Fluorine Doped Tin Oxide Films.” Applied Surface Science 256 (22). Elsevier B.V.: 6586–91. doi:10.1016/j.apsusc.2010.04.052.
Boskey, Adele. 2003. “Bone Mineral Crystal Size.” Osteoporos Int 14 ((Suppl 5)): S16–21. doi:10.1007/s00198-003-1468-2.
Mittemeijer, Eric J., and Udo Welzel. 2008. “The ‘State of the Art’ of the Diffraction Analysis of Crystallite Size and Lattice Strain.” Zeitschrift Fur Kristallographie 223 (9): 552–60. doi:10.1524/zkri.2008.1213.
Monshi, Ahmad. 2012. “Modified Scherrer Equation to Estimate More Accurately Nano-Crystallite Size Using XRD.” World Journal of Nano Science and Engineering 02 (03): 154–60. doi:10.4236/wjnse.2012.23020.
Ramezani, M, and T Neitzert. 2012. “Mechanical Milling of Aluminum Powder Using Planetary Ball Milling Process.” Journal of Achievements in Materials and Manufacturing Engineering 55 (2): 790–98. http://www.journalamme.org/papers_vol55_2/58288.pdf.
Supriyanto, Edy, and Ashanal Holikin. 2007. “Pengaruh Thermal Annealing Terhadap Struktur Kristal Dan Morfologi Bubuk Titanium Dioksida ( TiO 2 ) The Thermal Annealing Effect on Crystal Structure and Morphology of Titanium Dioxide ( TiO2 ) Powder” 15 (1): 37–41.
Suryanarayana, C. 2001. “Mechanical Alloying and Milling.” Progress in Materials Science.
Ullah, Mahbub, Eaqub Ali, Sharifah Bee, and Abd Hamid. 2014. “Surfactant-Assisted Ball Milling : A Novel Route To Novel Materials With Controlled Nanostructure - a Review.” Reviews in Advanced Materials Science 37: 1–14.
Werner, Anders, and Bredvei Skilbred. 2012. “Metallic Interconnects for Proton Ceramic Fuel Cells.” “X-Ray Diffraction : Debye-Scherrer Method.” 2004, 1–10.